PRODUCT SEARCH
Loading
Processing, Please wait...
67 part(s)
parts per page
PBPS71850ST
 
PBPS71850ST
Steel

Length: 18.50" 9 Bolt Holes Peterbilt Washer Bar

For under headers - between our 724 7241 rails

PBPS71900ST
 
PBPS71900ST
Steel

Header: 37.50" x 6.50" 42 Bolt Holes Peterbilt Bottom Tank

This is a blank low flow tank with a 1/4 " NPT flange for a drain cock.

PBPS71910ST
 
PBPS71910ST
Steel

Bracket: 22.00" x 6.50" 22 Bolt Holes

Matches 719 Bottom Tank

PBPS71920ST
 
PBPS71920ST
Steel

Peterbilt Bracket

Right side bottom mounting bracket.

PBPS71930ST
 
PBPS71930ST
Steel

Peterbilt Bracket

Left side bottom mounting bracket.

PBPS71950ST
 
PBPS71950ST
Steel

Header: 37.50" x 6.50" 42 Bolt Holes Peterbilt Bottom Tank

This tank is similar to tank719, except the 3.00 " diameter hose connection is curved back and up toward the engine.

PBPS71960ST
 
PBPS71960ST
Steel

Header: 31.25" x 6.00" 42 Bolt Holes Peterbilt Bottom Tank

This tank has a 1.25 " diameter hose connection, and a 3/8 " NPT flange. There is a cut-out in the center of the tank to accommodate a PTO.

PBPS71970ST
 
PBPS71970ST
Steel

Header: 31.25" x 6.00" 42 Bolt Holes Peterbilt Bottom Tank

This tank has a 2.50 " hose connection that points downwards then bends at a 90 degree angle towards the engine, and a 1/2 " NPT flange for a drain cock. Note: this tank shares a bolt pattern with tank #PB 511 and tank #PB 800.

PBPS71980ST
 
PBPS71980ST
Steel

Header: 31.25" x 6.00" 42 Bolt Holes Peterbilt Bottom Tank

This tank has a 2.50 " hose connection that points downward then angles at 90 degrees towards the driver side. There is a 1/4 " NPT flange at the bottom of the hose connection, and a PTO cutout in the center of the tank. Note: this tank shares a bolt pattern with tank #PB 511 and tank #PB 800.

PBPS71990ST
 
PBPS71990ST
Steel

Header: 37.50" x 6.50" 42 Bolt Holes Peterbilt Bottom Tank

This tank has a 3.00 " hose connection, 11.50 " from the edge of the tank to the center of the hose connection. The connection comes first straight down out of the tank, then bends at 90 degrees to face the engine. This tank is similar to the PB 7195, except that the hose connection does not sweep upward. Note: this tank shares the bolt hole pattern with tank #PB 719 and tank #PB 708.

PBPS72210ST
 
PBPS72210ST
Steel

Bracket: 25.50" x 6.50" 26 Bolt Holes

2 Mounting Holes @ 8.62 " Centers; Fits Peterbilt Bottom Tank # PB719; This bracket is 2.25 " Deep

PBPS72400ST
 
PBPS72400ST
Steel
Length: 36.25" Header: 6.50" x 9.37" Peterbilt Right Side Frame Rail
Top and bottom flanges each have 12 holes, ten drilled clearance for 5/16 " bolts and two tapped 5/16 " N.C. One bracket on side of channel near top with two holes drilled clearance for 1/2 " bolts. Angle brackets on each side of channel with 1/4 " N.C. threaded holes. Note: frames are not interchangeable. Order left or right accordingly.
PBPS72410ST
 
PBPS72410ST
Steel

Length: 36.25" Top Bottom Flanges: 6.50" x 9.37" Peterbilt Side Frame

Top and Btm flanges each have 12 holes, 2 tapped 5/16 " NC and 10 drilled clearance for 5/16 " bolts. Engine side of rail is flush with flanges with seven 1/4 " NC threaded holes. Six 1/4 " NC threaded holes on side. Two brackets on rail - one for CAC and one for mounting pin. NOTE: Frames are not interchangeable. Photo shown is Left side

PBPS95000ST
 
PBPS95000ST
Steel

Header: 29.12" x 3.00" Peterbilt Solder On Tank

PBPS95010ST
 
PBPS95010ST
Steel

Header: 33.25" x 3.00" Peterbilt Solder On Tank

PBPS95020ST
 
PBPS95020ST
Steel

Header: 34.12" x 3.50" Peterbilt Solder On Tank

PBPS95030ST
 
PBPS95030ST
Steel

Header: 16.00" x 3.00" Peterbilt Solder On Tank

2.25 " hose connection, 2.75 from end of tank to center of connection

PBPS95040ST
 
PBPS95040ST
Steel

Header: 26.25" x 2.75"Peterbilt Solder On Tank

Top and bottom tanks both have 2.50 " diameter hose connections, the top connection is in the center of the tank, and the bottom connection is 4.00 " from the end of tank to center of the hose connection.

67 part(s)
parts per page